Assessing the Interaction of Blanching and Drying Parameters in Yam Drying through Response Surface Methodology
DOI:
https://doi.org/10.56532/mjsat.v6i2.639Keywords:
Yam drying, RSM optimization, Yam blanching, Yam processing, Yam chipsAbstract
Blanching facilitates thermal energy utilization in yam drying by softening the tissue structure, so that heat penetrate more efficiently to minimize drying time. Higher drying temperatures further improve thermal energy utilization by accelerating moisture removal, though excessively high temperatures may reduce energy efficiency and product quality. The aforementioned conditions, including blanching time, has not been collectively run in any Response Surface Methodology (RSM) tool prior to this study, to test their effect on yam drying. In this study, Central Composite Design (CCD) in Design Expert 7.0 software was employed to assess the moisture content as response variable. Yam slices of 7–8 mm thickness were blanched at varying temperatures (70–90℃) and durations (15–35 min) and subsequently dried in a hot air tray dryer at temperatures between 50–70℃ for 4–10 h. The quadratic model showed an excellent fit with an R2 value of 0.9750 and 95% confidence intervals. Among the tested interactions, the combination of blanching temperature and blanching duration exhibited a strong synergistic effect on moisture removal efficiency. The optimal conditions – blanching at 90℃ for 23.9 min and drying at 70℃ for 10 h, resulted in a minimum moisture content of 3.99% with a desirability of 0.812. It further signifies a high thermal efficiency and minimal energy loss. Hence, the findings demonstrate the process’s potential for yam flour production, due to its effective dehydration, nutrient preservation, and energy-efficient drying performance. Attention must be given to differences in yam types, which currently includes, white yam, yellow yam, bitter yam, water yam and three-leaved yam, when opting for drying RSM, kinetics and thermodynamic studies.
References
N. Verter and V. Bečvářová, “An analysis of yam production in Nigeria,” Acta Univ. Agric. Silvic. Mendelianae Brun., vol. 63, no. 2, pp. 659–665, 2015, doi: https://doi.org/10.11118/actaun201563020659.
P. E. Adejo, “Post-harvest management Practices of yam and farmers’ information needs in the North-Central of Nigeria,” J. Nutraceuticals Food Sci., vol. 2, no. 3, pp. 1–7, 2017, [Online]. Available: http://nutraceuticals.imedpub.com/archive.php
E.-O. S. Ema, J. E. Obidiegwu, C. A. Chilaka, and E. M. Akpabio, “Indigenous food yam cultivation and livelihood practices in Cross River state, Nigeria,” World, vol. 4, no. 2, 2023, doi: https://doi.org/10.3390/world4020020.
A. S. Oladipo, F. T. Fayose, and O. E. Omofunmi, “A review of the performance of made in Nigeria yam processing machines,” J. Res. For. Wildl. Environ., vol. 12, no. 4, pp. 135–141, 2020, [Online]. Available: https://www.ajol.info/index.php/jrfwe/article/view/204362
B. A. Adeleye, A. Rahman, and A. O. Raji, “Optimization of yam milling-A response surface approach,” Adv. J. Food Sci. Technol., vol. 4, no. 4, pp. 189–194, 2012, [Online]. Available: https://maxwellsci.com/print/ajfst/v4-189-194.pdf
A. A. Olawore, “Social relations of yam flour production and distribution in Lagos and Oyo states, Nigeria,” Doctor of Philosophy Thesis, Department of Sociology, Faculty of The Social Sciences, University of Ibadan, 2023. [Online]. Available: http://repository.pgcollege.ui.edu.ng:8080/xmlui/handle/123456789/2196
A. D. Chinedu, “The production of yam flour,” Degree of Bachelor of Engineering (B.Eng), Department of Chemical Engineering, Faculty of Engineering, Caritas University, 2013. [Online]. Available: https://pub.abuad.edu.ng/Open_Access_Research_Projects_of_Universities_-
L. Li, M. Zhang, and B. Bhandari, “Influence of drying methods on some physicochemical, functional and pasting properties of Chinese yam flour,” LWT, vol. 111, pp. 182–189, 2019, doi: https://doi.org/10.1016/j.lwt.2019.05.034.
C. Omohimi et al., “Safety of yam-derived (Dioscorea rotundata) foodstuffs—Chips, flakes and flour: Effect of processing and post-processing conditions,” Foods, vol. 8, no. 1, 2019, doi: https://doi.org/10.3390/foods8010012.
D. Zou et al., “Modeling and comparative analysis of solar drying behavior of yam (Rhizoma dioscoreae) slices,” Renew. Energy Power Qual. J., vol. 242, no. 122406, 2025, doi: https://doi.org/10.1016/j.renene.2025.122406.
K. Nwosu-Obieogu, E. O. Oke, and S. Bright, “Energy and exergy analysis of three leaved yam starch drying in a tray dryer: Parametric, modelling and optimization studies,” Heliyon, vol. 8, no. 8, pp. 1–10, 2022, doi: https://doi.org/10.1016/j.heliyon.2022.e10124.
A. A. Okunola et al., “Drying characteristics, kinetic modeling, energy and exergy analyses of water Yam (Dioscorea alata) in a hot air dryer,” Energies, vol. 16, no. 4, 2023, doi: https://doi.org/10.3390/en16041569.
J. O. Ojediran et al., “Drying characteristics of yam slices (Dioscorea rotundata) in a convective hot air dryer: Application of ANFIS in the prediction of drying kinetics,” Heliyon, vol. 6, no. 3, pp. 1–12, 2020, doi: https://doi.org/10.1016/j.heliyon.2020.e03555.
Z. Huang, H. Li, K. A. Addo, Y. Yu, and X. Xiao, “Optimization of preparation technology of purple yam slices by Response Surface Methodology and study of its antioxidant activity,” in Proceedings of the National Academy of Sciences, India Section B: Biological Sciences, 2025, pp. 105–116. doi: https://doi.org/10.1007/s40011-024-01598-0.
X. Lei et al., “Optimization of microwave vacuum drying technology of yam and the evaluation of its functional activity,” Food Mach., vol. 35, no. 6, pp. 188–194, 2019, doi: https://doi.org/10.13652/j.issn.1003-5788.2019.06.034.
F. Stolp, “Modelling and improving the nutritional content of yam during drying,” MSc Thesis Biobased Chemistry and Technology, Sustainable Food Process Engineering, Agrotechnology and Food Science, Wageningen University, 2015. [Online]. Available: https://edepot.wur.nl/333937
S. A. Aasa, O. O. Ajayi, and O. A. Omotosho, “Design optimization of hot air dryer for yam flour chunk,” Asian J. Sci. Res., vol. 5, no. 3, pp. 143–152, 2012, doi: https://doi.org/10.3923/ajsr.2012.143.152.
O. P. Sobukola, S. O. Awonorin, L. O. Sanni, and F. O. Bamiro, “Optimization of blanching conditions prior to deep fat frying of yam slices,” Int. J. Food Prop., vol. 11, no. 2, pp. 379–391, 2008, doi: https://doi.org/10.1080/10942910701409294.
O. F. Olagunju-Yusuf, A.-R. Adebowale, O. Sobukola, and L. Sanni, “The optimization of production of instant pounded yam flour using cultivars of white yam (Dioscorea rotundata),” Asian Food Sci. J., vol. 13, no. 4, pp. 1–9, 2019, doi: https://doi.org/10.9734/AFSJ/2019/v13i430113.
O. P. Sobukola, S. O. Awonorin, S. L. Oladimeji, and B. F. Olukayode, “Optimization of pre-fry drying of yam slices using Response Surface Methodology,” J. Food Process Eng., vol. 33, no. 4, pp. 626–648, 2010, doi: https://doi.org/10.1111/j.1745-4530.2008.00293.x.
J. Zhang, X. Zheng, H. Xiao, C. Shan, Y. Li, and T. Yang, “Quality and process optimization of infrared combined hot air drying of yam slices based on BP neural network and Gray Wolf Algorithm,” Foods, vol. 13, no. 3, 2024, doi: https://doi.org/10.3390/foods13030434.
M. Abud-Archila et al., “Optimization of osmotic dehydration of yam bean (Pachyrhizus erosus) using an orthogonal experimental design,” J. Food Eng., vol. 84, no. 3, pp. 413–419, 2008, doi: https://doi.org/10.1016/j.jfoodeng.2007.06.003.
E. C. Nwadike, M. N. Abonyi, J. T. Nwabanne, and P. E. Ohale, “Optimization of solar drying of blanched and unblanched aerial yam using Response Surface Methodology,” Int. J. Trend Sci. Res. Dev., vol. 4, no. 3, pp. 659–666, 2020, [Online]. Available: https://www.ijtsrd.com/engineering/mechanical-engineering/30598
B. A. Adejumo, R. U. Ajibo, and P. A. Obasa, “Optimization of soaking condition and drying temperature for the production of African yam beans (Sphenostylis sternocarpa) flour,” in Food Security and Safety, O. O. Babalola, Ed., Springer, Cham, 2021, pp. 63–95. doi: https://doi.org/10.1007/978-3-030-50672-8_4.
E. N. Amedor, F. Sarpong, P. K. Bordoh, E. F. Boateng, and J. Owusu-Kwarteng, “Modelling convectional oven drying characteristics and energy consumption of dehydrated yam (Dioscorea rotundata) chips,” Heliyon, vol. 10, no. 14, pp. 1–19, 2024, doi: https://doi.org/10.1016/j.heliyon.2024.e34672.
H. Wang, D. Liu, H. Yu, D. Wang, and J. Li, “Optimization of microwave coupled hot air drying for Chinese yam using Response Surface Methodology,” Processes, vol. 7, no. 10, 2019, doi: https://doi.org/10.3390/pr7100745.
Y.-P. Lin, T.-Y. Lee, J.-H. Tsen, and V. A.-E. King, “Dehydration of yam slices using FIR-assisted freeze drying,” J. Food Eng., vol. 79, no. 4, pp. 1295–1301, 2007, doi: https://doi.org/10.1016/j.jfoodeng.2006.04.018.
N. A. G. Aneke, G. O. Mbah, and N. J. Edeani, “Response Surface Methodology for optimisation of hot air drying of water yam slices,” Int. J. Sci. Res. Publ., vol. 8, no. 8, pp. 248–259, 2018, doi: https://doi.org/10.29322/IJSRP.8.8.2018.p8030.
L. Li, M. Zhang, and P. Yang, “Suitability of LF-NMR to analysis water state and predict dielectric properties of Chinese yam during microwave vacuum drying,” LWT, vol. 105, pp. 257–264, 2019, doi: https://doi.org/10.1016/j.lwt.2019.02.017.
C. Ononogbo et al., “Thermal efficiency and drying behaviour of yam slices in a dryer driven by the waste heat of exhaust gases,” Sci. African, vol. 17, no. e01310, 2022, doi: https://doi.org/10.1016/j.sciaf.2022.e01310.
L. Li, M. Zhang, and L. Zhou, “A promising pulse-spouted microwave freeze drying method used for Chinese yam cubes dehydration: Quality, energy consumption, and uniformity,” Dry. Technol., vol. 39, no. 2, pp. 148–161, 2019, doi: https://doi.org/10.1080/07373937.2019.1624564.
E. E. Abano and R. S. Amoah, “Microwave and blanch-assisted drying of white yam (Dioscorea rotundata),” Food Sci. Nutr., vol. 3, no. 6, pp. 586–596, 2015, doi: https://doi.org/10.1002/fsn3.249.
O. Chibuike, N. O. Chukwudozie, N. N. Reginald, O. C. Anthony, I. O. Johnson, and E. E. Anyanwu, “Energy consumption of yam slice drying in an exhaust gas waste heat recovery hot air tray dryer,” Sci. Res. J., vol. IX, no. VIII, pp. 1–7, 2021, doi: https://doi.org/10.31364/SCIRJ/v9.i08.2021.P0821872.
K. C. Yadav, R. Rajbanshi, N. Katuwal, P. Dhungana, and D. Subba, “Process optimization for yam flour incorporated in expanded extrudates,” Int. J. Food Prop., vol. 24, no. 1, pp. 1252–1264, 2021, doi: https://doi.org/10.1080/10942912.2021.1958839.
L. Q. Ming, L. Z. Ya, Z. L. Ru, Z. X. Mei, X. X. Yao, and S. X. Jun, “Optimization of explosion puffing drying process of yam slice and study of its properties,” J. South. Agric., vol. 47, no. 10, pp. 1743–1748, 2016, [Online]. Available: https://www.cabidigitallibrary.org/doi/full/10.5555/20173158675
M. L. Na, R. C. Qing, Z. X. Zhi, and C. Yang, “Optimization of the vacuum freeze drying process of Chinese yam slices,” J. Food Saf. Qual., vol. 8, no. 9, pp. 3466–3472, 2017, [Online]. Available: http://www.chinafoodj.com/
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Yusufu Luka, Abdulhalim Musa Abubakar, Michael Mshirshima Tsaha, Semiu Adebayo Kareem
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
